Torch and File
My Account
Home >  Head Tube Mill

T&F HEAD TUBE MILL w/ SILVA no. 405 FOR 1-1/8" STEERERS

Part Number HTM002
review 0 Review(s)
0
T&F HEAD TUBE MILL w/ SILVA no. 405 FOR 1-1/8" STEERERS
T&F HEAD TUBE MILL w/ SILVA no. 405 FOR 1-1/8' STEERERS
Email a friend Email a friend
Review this item Review this item
Price
Your Price:   $638.00
On sale: 
$595.00
On Sale
Availability:
In Stock
Quantity
Add to Gift Registry
Description
Head tube mill complete with SILVA Art 405 cutter for 1-1/8" steerers Note: the complete range of SILVA head tube cutters fit on this holder - just purchase different cutters and you're good to go.  Note: spare SSH001 stainless steel handles no. 160 are shown in the FRAMEBUILDING TOOLS - "MISCELLANEOUS" section.  

OPERATING INSTRUCTIONS FOR THE T&F/SILVA HEAD TUBE MILL


1)  Slide the SILVA head tube reamer/facer cutter onto the arbor (held inside the mill handle body).  Tighten the arbor draw bolt with a 6mm Allen wrench securing the arbor and cutter to the mill body.  Note:  arbor has 20.5mm o.d. and accepts all sizes of SILVA reamer/facers.


2)  Slide aligning cone onto the bottom spot faced end of the arbor guide tube and tighten the cone securing bolt with 6mm Allen wrench.


3)  Assemble the compression rod first threading the brass Acme square nut a few turns then thread the round steel knob to the end below the Acme threaded portion and secure by tightening the set screw. Drop the spring over the rod to rest on the nut.


4)  Pass the assembled compression rod/Acme nut/spring into the bottom spot faced end of the arbor guide tube.  Place the mill body into one end of the head tube then pass the compression rod/arbor guide tube through the opposite end of the head tube and screw the rod into the mill arbor.


5)  Tighten the brass Acme square nut to apply spring force to load the guide tube against the arbor then loosen the cone securing bolt and slide the cone up to the head tube and tighten the bolt with a 6mm Allen wrench.


6)  Loosen the arbor draw bolt 12 turns.  This allows the arbor guide tube to descend into the head tube applying a 15mm preload.  Loosen the cone securing bolt and slide the cone snug up against the head tube and tighten the cone bolt.  Tighten the arbor draw bolt drawing the arbor and cutter back up into the mill body.


7)  Proceed to mill the head tube.  Tighten the brass Acme square nut some during the reaming operation if needed to increase the spring load.  Reverse and mill the other end of the head tube.


Related Items
HEAD TUBE CUTTER SILVA no. 044
HEAD TUBE CUTTER SILVA no. 044
Average Rating 0 Review(s)
Your Price: $205.60
HEAD TUBE CUTTER SILVA no. 405 FOR 1-1/8
HEAD TUBE CUTTER SILVA no. 405 FOR 1-1/8" STEERERS
Average Rating 1 Review(s)
Your Price: $297.50
T&F HEAD TUBE MILL w/ SILVA no. 044 CUTTER FOR 1
T&F HEAD TUBE MILL w/ SILVA no. 044 CUTTER FOR 1" STEERERS
Average Rating 0 Review(s)
Your Price: $543.00
On sale: $505.00 On Sale
HEAD TUBE MILL, SILVA no. 053 FOR 1
HEAD TUBE MILL, SILVA no. 053 FOR 1" STEERERS
Average Rating 1 Review(s)
Your Price: $1,018.17
On sale: $814.54 On Sale
HEAD TUBE MILL SILVA no.054 FOR 1-1/8
HEAD TUBE MILL SILVA no.054 FOR 1-1/8" STEERERS
Average Rating 0 Review(s)
Your Price: $1,063.67
HEAD TUBE MILL SILVA NO. 059A 44MM HEAD TUBE
HEAD TUBE MILL SILVA NO. 059A 44MM HEAD TUBE
Average Rating 0 Review(s)
Your Price: $1,483.33
On sale: $1,186.66 On Sale
Recently Viewed Items
Browse Similar Items